©2011 JELD-WEN, inc.; This publication and its contents are owned by JELD-WEN, inc. and are protected under the U.S. Copyright Act and other intellectual property laws.
All trademarks, service marks, logos and the like (whether registered or unregistered) are owned or controlled by JELD-WEN, inc. or others.
Unauthorized use or duplication of JELD-WEN intellectual property is prohibited.
JELD-WEN reserves the right to change product specications without notice. Please check our website, jeld-wen.com, for current information.
INSTALLATION INSTRUCTIONS
for Entry Door Jamb Extension Kits
KIT INCLUDES:
•2-Sidejambpieces
•1-Headjambpiece
•1-Sillextender
NEEDED TOOLS:
•Pencil
•Measuringtape
•Saw
•Drillwithbits
•Caulkinggun
•Puttyknife
•Clamps
•Prybar
NEEDED MATERIALS:
•#8x21/2"deck
screws
•Sealant(paintable)
•Woodputtyor
spackle
•Finishingsupplies
Thank you for selecting JELD-WEN products. Attached are JELD-WEN’s
recommended installation instructions for 2" Exterior Door Jamb
Extension Kits. This kit converts a 4 9/16" jamb to a 6 9/16" jamb.
1. Carefully pry or cut off existing brickmould trim from the existing
frame if installed.
2. Toinstallthesillextender,
tilttheextenderupat45
degreeangletohookonto
noseofsillandlineupush
withedges.Pushthefront
ofextenderdownandstep
ontheextendertosnapit
intoplace.
3. Eachsidejambextenderis
beveledononeendtot
theproleofthesloped
sill.Thereisarightanda
leftpiece.Placeagainst
thejambushwiththe
insideofthejamb,withthe
bevelededgeonthesill
(highsideofbeveltowards
door).
4. Markthesidejamb
extendersushwith
thetopoutsideedgeof
jambasshownandcutto
length.Pre-drilla1/8"hole
horizontallycentered(orin
thekerf(groove)ifpresent)
ineachextender1"from
eachendand3more
evenlyspacedbetweenthe
rsttwoineachextender.
5. Runa1/4"beadofsealant
alongthebottomof
theextenderwhereitis
notchedtocontactthe
sillandupthelength
ofextenderthatwillbe
againstjambasshown.
6. Secure the extenders to
jamb (clamp in place if
necessary) with 2 1/2"
deck screws through the
previously-drilled holes.
Set screw heads 1/4" below
surface.
7. Measure the distance
between the two side
jamb extenders and cut the
head extender to length.
Pre-drill a 1/8" hole 1"
from each end and 1 hole
in the center. Apply a 1/4"
bead of sealant the length
of extender on face that
will be against the jamb.
Secure to jamb with 2 1/2"
deck screws through the
pre drilled holes. Set screw
heads 1/4" below surface.
8. Fillallholeswithwoodputtyorspackling.Sealantcanbeapplied
andsmoothedtothejointbetweentheextendersandtheexisting
jambandsillforaseamlessappearance.
9. Runabeadofsealantalongthejointwherethejambextenders
meetthesilloneachend.
10.Finishallexposedwoodpartswithtopqualityproducts.
Pleasevisitjeld-wen.com/resourcesforwarranty
andcareandmaintenanceinformation.
Thankyouforchoosing
(12/11)
Measurehere
Extender
Sill
extender
Existing
jamb
Cuthere
Side
against
jamb
Sillnotch
Bottom
Commentaires sur ces manuels